Acetylcarnitine (ALCAR), Pan-species (General) CLIA Kit
Katalog-Nummer CCO400Ge-24
Size : 24tests
Marke : USCN
Contact local distributor :
Telefonnummer : +1 850 650 7790
CLIA Kit for Acetylcarnitine (ALCAR)
Acetyl-L-carnitine
- Product No.CCO400Ge
- Organism SpeciesPan-species (General) Same name, Different species.
- Test MethodCompetitive Inhibition
- Assay Length2h
- Detection Range19.5-5,000ng/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 7.7ng/mL.
- Sample Typeserum, plasma and other biological fluids
- Download Instruction Manual
- UOM 48T96T 96T*5 96T*10 96T*100
-
Packages (Simulation) -
Packages (Simulation)
-
Results demonstration
- Typical Standard Curve
-
ISO9001: 2008, ISO13485: 2003 Registered
Specificity of the CLIA Kit for Acetylcarnitine (ALCAR)
This assay has high sensitivity and excellent specificity for detection of Acetylcarnitine (ALCAR).
No significant cross-reactivity or interference between Acetylcarnitine (ALCAR) and analogues was observed.
Recovery of the CLIA Kit for Acetylcarnitine (ALCAR)
Matrices listed below were spiked with certain level of Acetylcarnitine (ALCAR) and the recovery rates were calculated by comparing the measured value to the expected amount of Acetylcarnitine (ALCAR) in samples.
| Matrix | Recovery range (%) | Average(%) |
| serum(n=5) | 87-97 | 90 |
| EDTA plasma(n=5) | 96-105 | 101 |
| heparin plasma(n=5) | 91-99 | 94 |
Precision of the CLIA Kit for Acetylcarnitine (ALCAR)
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Acetylcarnitine (ALCAR) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Acetylcarnitine (ALCAR) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%
Linearity of the CLIA Kit for Acetylcarnitine (ALCAR)
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Acetylcarnitine (ALCAR) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
| Sample | 1:2 | 1:4 | 1:8 | 1:16 |
| serum(n=5) | 82-92% | 90-102% | 94-104% | 99-105% |
| EDTA plasma(n=5) | 79-95% | 97-104% | 91-105% | 85-101% |
| heparin plasma(n=5) | 79-98% | 87-101% | 80-95% | 95-103% |
Stability of the CLIA Kit for Acetylcarnitine (ALCAR)
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Assay procedure summary of the CLIA Kit for Acetylcarnitine (ALCAR)
1. Prepare all reagents, samples and standards;
2. Add 50µL standard or sample to each well.
And then add 50µL prepared Detection Reagent A immediately.
Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
7. Read RLU value immediately.
Test principle of the CLIA Kit for Acetylcarnitine (ALCAR)
The microplate provided in this kit has been pre-coated with a monoclonal antibody specific to Acetylcarnitine (ALCAR). A competitive inhibition reaction is launched between biotin labeled Acetylcarnitine (ALCAR) and unlabeled Acetylcarnitine (ALCAR) (Standards or samples) with the pre-coated antibody specific to Acetylcarnitine (ALCAR). After incubation the unbound conjugate is washed off. Next, avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. The amount of bound HRP conjugate is reverse proportional to the concentration of Acetylcarnitine (ALCAR) in the sample. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is reverse proportional to the Acetylcarnitine (ALCAR) level in the sample or standard.